linux:megaraid
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
linux:megaraid [2011/09/29 22:10] walter |
linux:megaraid [2021/05/02 21:36] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== MegaraidCLI ====== | ||
| + | |||
| + | **Page Under Construction, is based off of the megaraid pdf on the main page** | ||
| + | |||
| + | ---- | ||
| + | |||
| The MegaRaid cli utility is used to talk to LSI MegaRaid controllers, such as the one in the PowerEdge 2950 which is re-branded by Dell as the perc5. The utility exists in the AUR (Arch User Repository) and is installed in /opt. | The MegaRaid cli utility is used to talk to LSI MegaRaid controllers, such as the one in the PowerEdge 2950 which is re-branded by Dell as the perc5. The utility exists in the AUR (Arch User Repository) and is installed in /opt. | ||
| + | |||
| + | ====== Command Flags ====== | ||
| ^ Flag ^ Description ^ | ^ Flag ^ Description ^ | ||
| Line 13: | Line 21: | ||
| |{ } | Indicates that the parameters are grouped and that they must be given at the same time. | | |{ } | Indicates that the parameters are grouped and that they must be given at the same time. | | ||
| - | ^Command ^Description | + | ====== Get Adapter Info ====== |
| - | | MegaCli -AdpAllinfo -aN ¦-a0,1,2¦-aALL | Displays information about the controller, including cluster state, BIOS, alarm, firmware version, BIOS version, battery charge counter value, rebuild rate, bus number/device number, present RAM, memory size, serial number of the board, and SAS address. | | + | <code> |
| + | MegaCli -AdpAllinfo -aN ¦-a0,1,2¦-aALL | ||
| + | </code> | ||
| + | Displays information about the controller, including cluster state, BIOS, alarm, firmware version, BIOS version, battery charge counter value, rebuild rate, bus number/device number, present RAM, memory size, serial number of the board, and SAS address. | ||
| ====== Controller Properties ====== | ====== Controller Properties ====== | ||
| Line 97: | Line 108: | ||
| <code> | <code> | ||
| MegaCli -AdpFacDefSet -aN|-a0,1,2|-aALL | MegaCli -AdpFacDefSet -aN|-a0,1,2|-aALL | ||
| - | </code | + | </code> |
| ===== Set Time and Date on Controller ===== | ===== Set Time and Date on Controller ===== | ||
| Line 106: | Line 117: | ||
| ===== Display Time and Date on Controller ===== | ===== Display Time and Date on Controller ===== | ||
| <code> | <code> | ||
| - | MegaCli –AdpSetTime yyyymmdd HH:mm:ss -aN|-a0,1,2|-aALL | + | MegaCli –AdpGetTime -aN |
| </code> | </code> | ||
| + | |||
| + | ===== Patrol Read Controller Properties ===== | ||
| + | |||
| + | A Patrol Read scans the system for possible drive errors that could | ||
| + | lead to drive failure, then takes action to correct the errors. | ||
| + | The goal is to protect data integrity by detecting drive failure before the failure can | ||
| + | damage data. The corrective actions depend on the virtual drive | ||
| + | configuration and the type of errors. Patrol Read affects performance; the | ||
| + | more iterations there are, the greater the impact. | ||
| + | |||
| + | ==== Set Patrol Read Options ==== | ||
| + | |||
| + | <code> | ||
| + | MegaCli –AdpPR –Dsbl|EnblAuto|EnblMan|Start|Stop|Info -aN| | ||
| + | -a0,1,2|-aALL | ||
| + | </code> | ||
| + | <code> | ||
| + | -Dsbl: Disables Patrol Read for the selected controller(s). | ||
| + | -EnblAuto: Enables Patrol Read automatically for the selected controller(s). | ||
| + | This means Patrol Read will start automatically after the controller initialization is | ||
| + | complete. | ||
| + | -EnblMan: Enables Patrol Read manually for the selected controller(s). This means | ||
| + | that Patrol Read does not start automatically; it has to be started manually by | ||
| + | selecting the Start command. | ||
| + | -Start: Starts Patrol Read for the selected controller(s). | ||
| + | -Stop: Stops Patrol Read for the selected controller(s). | ||
| + | -Info: Displays the following Patrol Read information for the selected controller(s): | ||
| + | * Patrol Read operation mode | ||
| + | * Patrol Read execution delay value | ||
| + | * Patrol Read status | ||
| + | </code> | ||
| + | |||
| + | ==== Set Patrol Read Delay Interval ==== | ||
| + | Sets the time between Patrol Read iterations. | ||
| + | |||
| + | <code></code> | ||
| + | |||
| + | |||
linux/megaraid.1317334259.txt.gz · Last modified: 2021/05/02 21:36 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
